****** - Verified Buyer
4.5
Once you up your temps a bit this stuff works well! There is a bit of a learning curve and I had to set my temps a bit higher than the label recommends, but this stuff looks great once you figure it out!It takes a lot to make this glow, I had to put a light almost directly on it to “charge” it. The light that worked best was an UV light.What do I need to do to make this junk glow? ..put it out in the sun? I left it under a bright light for over an hour and it has just a slight glow. Wish I had used it sooner. I waited to long to return it.UPDATE: They sent me a new roll for free and it glows much better. Great response by seller. Kudos.This stuff is very accurate and prints quite well.I get worry free printing with a quality that I can expect and reproduce.Layer adhesion is great, strength is great.Bonus: It glows.Loved the color & feel of this filament! Definitely my goto for wood filamentWith my very first 3D printer, I could only print with ABS. At that time, I frequently printed in a Glow ABS. Kids just seem to be really intrigued by Glow-in-the-Dark items and it was a big seller back then. I have looked for PLA in a glow for quite some time and the only items I found were way to over priced for my tastes. Then I stumbled across ISANMATE's Glow in the Dark Filament and decided to give it a go. When the box arrived and I opened it, I saw the same quality packaging that I always see in ISANMATE's filaments, solid box with a nicely vacuum packaged roll of filament. Removing it from the package only took a few minutes and it was set to print. I really appreciate the quality of the spooling of the filament. Nice even rows of filament shows that ISANMATE takes the time to get it right the first time. I normally do a test print, without running a Temp Tower, just to see hoe the filament prints with "Standard Settings" The Benchy printed beautifully on my MK3s. Once the print was done, I let the print sit in the bed and cool and soak in the light. Then I turned off the lights to see how well the glow would show. Some filament I have tried in the past, had a very low glow and it was difficult to take photos without adding some additional light. Not so for this filament, these photos are straight from my phone. There is a little bit of stringing visible but a few extra degrees of heat will fix that and then these will be perfect. The last image is what 3D printing is all about. Our old Christmas tree star died and we had to buy a new one. The star came with a terrible mount that looked like it was made from the top of a milk carton. as tall as our tree id, the star would never fit on top with that stupid mount. I took the mount from the old star and testid it. The "Chip Clip" design is great and allows the star to be mounted lower on the tree and that way it clears the ceiling. The mount had a green tube on top that fit the old star but didn't fit the new one, it was bigger. After 15 minutes of time in the modeling software and 30 minutes of print time and the new star was on the tree. The glow filament isn't as white/white as the star but buried in the tree, you'll never notice.All in all, I have come to like ISANMATE's filament and the price is very hard to beat. If you need to GLOW, give this filament a try!!Keep in mind when working with glow in the dark. I you use it frequently be prepared to purchase more nozzles. Great strong quality. But hard on brass .Da ich in der Regel meistens kleinere Modell drucke, dachte ich es wäre Cool etwas mehr Farbe auf die Fensterbank zu bekommen, Leider erfuhr ich erst auf Anfrage beim Hersteller, dass ein Wechsel ab ca. 120 g statt findet. Tja leider als ich dann ein Paar gedruckt hatte, war das Filament alle und bei kleinen Models ist dieser Effekt nicht wirklich erkennbar, da meine Modele einfach zu klein sind.Qidi Max, 195 Grad, 40 Grad Heizbett, keine Stützen bei meinem Model, Schichtdicke 0.2, Linienbreite 0.4, keine Druckplattenunterstützung und kein Drucken im VorausEin Großes Plus, an den Hersteller, Support Anfrage, schnelle Antwort, Danke!Würde das Filament wieder kaufen, im Fall dass ich mal etwas größeres Drucken möchte, in diesem Fall Kaufempfehlung.Very nice filament has a great carbon fiber look to the exterior. Printed at 210c on 60c bed using an Ender 3 v2. The adhesion is fantastic with it, really need to let the bed cool fully before removing a print.Pictured in review is a watch stand I printed using this filament.Could not get good results, seems to melt really easy but not consistent and clogged nozzle several times, I’m going back to the cf that actually gets good results, this was a big waste of time and money for me, I went with this brand to save $10 per roll and it cost me way way more , I’d avoid this at all costsEmpacado al vacío. Buen filamento sin problemas para trabajarlo y gran iluminación y duración.Druckt super. Leuchtet nichts. Egal wie groß das gedruckte ist
